ramps_marlin_3d_printer
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
ramps_marlin_3d_printer [2018/03/27 18:39] 66.190.155.97 |
ramps_marlin_3d_printer [2020/04/21 19:24] 99.187.157.162 |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ===== RAMPS/Marlin 3D Printer ===== | + | RETIRED ===== RAMPS/Marlin 3D Printer ===== RETIRED |
| PLEASE NOTE: You may **NOT** use this machine prior to being checked out on it. | PLEASE NOTE: You may **NOT** use this machine prior to being checked out on it. | ||
| Line 13: | Line 13: | ||
| [[https://www.repetier.com/|Repetier]] | [[https://www.repetier.com/|Repetier]] | ||
| [[http://www.zyltech.com/extruder.html|Extruder]]\\ | [[http://www.zyltech.com/extruder.html|Extruder]]\\ | ||
| - | **Working Condition**: yes \\ | + | **Working Condition**: no \\ |
| **Contact**: Steve A. \\ | **Contact**: Steve A. \\ | ||
| Line 30: | Line 30: | ||
| ==== Usage Instructions ==== | ==== Usage Instructions ==== | ||
| - Power on the laptop and open Repetier_Host from the Desktop. | - Power on the laptop and open Repetier_Host from the Desktop. | ||
| - | - To turn on the 3D printer, flip the switch connection the black and green wires glued to the top of the power supply. DANGER: The heated bed uses 120V AC power, which is connected through the small board at the bottom center of the printer. Be very careful when reaching inside the printer not to touch any wires. If the switch has come unglued from the top of the power supply, do NOT reach into the wires at the bottom to retrieve it without ensuring BOTH power cords are unplugged. Notify a board member immediately if the power switch has come unglued from the top of the power supply. | + | - To turn on the 3D printer, flip the switch connecting the black and green wires glued to the top of the power supply. DANGER: The heated bed uses 120V AC power, which is connected through the small board at the bottom center of the printer. Be very careful when reaching inside the printer not to touch any wires. If the switch has come unglued from the top of the power supply, do NOT reach into the wires at the bottom to retrieve it without ensuring BOTH power cords are unplugged. Notify a board member immediately if the power switch has come unglued from the top of the power supply. |
| - In the upper left corner of Repetier, click the arrow next to the Connect button and select the RepRap_Marlin machine. The button should change to a Disconnect button once connected. If the button says Disconnect when you open the laptop, the laptop is already connected to the printer. | - In the upper left corner of Repetier, click the arrow next to the Connect button and select the RepRap_Marlin machine. The button should change to a Disconnect button once connected. If the button says Disconnect when you open the laptop, the laptop is already connected to the printer. | ||
| - Load an .stl file using the Load button. An image of your piece should appear in the 3D View tab. you can manipulate the object using the Object Placement tab on the right side of the screen. | - Load an .stl file using the Load button. An image of your piece should appear in the 3D View tab. you can manipulate the object using the Object Placement tab on the right side of the screen. | ||
ramps_marlin_3d_printer.txt ยท Last modified: 2020/04/21 19:24 by 99.187.157.162
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
