Page locked

This page is currently locked for editing by another user. You have to wait until this user finishes editing or the lock expires.

Currently locked by: 3.145.23.123
Lock expires at: 2024/04/28 19:45 (10 min)

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.

===== Laser Cutter/Engraver =====

PLEASE NOTE: You may **NOT** use this machine prior to being checked out on it.

**Owner/Loaner**: Asheville Makers \\
**Donated By**: N/A \\
**Serial Number**: N/A \\
**Make/Model**: [[http://www.ebay.com/itm/High-Precise-USB-Port-Laser-Engraving-Cutting-Machine-Engraver-Cutter-60W-CO2-/262600263802?hash=item3d2432087a:g:rEIAAOSwgmJXxPA7|K60]] \\
**Arrival Date**: September 2016 \\
**Working Condition**: yes \\
**Contact**: Any Board Member \\
**Manual**: Located in bag on shelf above machine

====Usage Notes====
  * DO NOT use this machine if you have not been checked out on it.  Members who can check you out include Tim, Zak, Avi, and Steve.
  * Running the laser at full power will significantly shorten the laser life.  The maximum power setting used should be 80%.
  * Certain materials can release dangerous and damaging fumes when cut or engraved.  DO NOT cut any material unless you know exactly what the material is and that it is safe to cut/engrave.  See this [[http://atxhackerspace.org/wiki/Laser_Cutter_Materials|page]] for more information.  Note that this should not be considered the final authority - it is your responsibility to know what you are cutting and whether it is safe.

====Tutorials====
  * [[https://drive.google.com/open?id=0ByE4uXHeoDYNUU1vM1Nuczc0Mjg|Power up and power down]]
  * [[https://drive.google.com/open?id=0ByE4uXHeoDYNYk1ySV83R0JGVWc|Loading and running files from a USB drive]]
  * [[https://www.youtube.com/user/SarbarMultimedia|Series of videos about using this machine and the control software RDWorks]]

====Post Processing====
  * [[http://support.epiloglaser.com/article/8205/30190/easily-remove-engraving-residue-from-wood|Easily Remove Engraving Residue from Wood]]

====Materials====
  * [[http://atxhackerspace.org/wiki/Laser_Cutter_Materials|Here is a good summary]] of some materials that may and may not be used on the laser cutter/engraver.
  * [[http://tcmaker.org/wiki/index.php?title=Laser_Cutter_Materials|Here is another]], which adds galvanized metal and mirrored surfaces to the list of material not to use.
  * These lists may not be all inclusive.  It is YOUR responsibility to know exactly what material you are cutting and whether or not it is safe.  If you are unsure, DO NOT USE IT!

====Settings====
Please share your experiences here with settings that gave you good results.
==8mm acrylic/plexiglass==
  Cut        Speed: 10   Power: 60
  Engrave    Speed: 200  Power: 20
==Soft Pine==
  Engrave    Speed: 250  Power: 30
  This engraved with just a little depth.  Less power if you just want to color the surface.
==White Office Paper (cuts nicely - great for prototyping)==
  Cut:       Speed: 100  Power: 25
  Engrave    Speed: 100  Power: 10
  I engraved in Cut mode, not Scan mode.  With this setting, the laser burnt a fine, brown outline on the paper.
==1/4 in. plywood==
  Cut        Speed: 10   Power: 60
  Engrave    Speed: 200  Power: 20
==1/4 in. plywood New 2" PL Lens==
  Cut        Speed: 15   Power: 55-60
==Corrugated Cardboard==
  Cut        Speed: 40   Power: 45
  Engrave    Speed:      Power: 
==Very Thin Wood Veneer==
  Cut        Speed: 100  Power: 40
  Engrave    Speed:      Power:

Asheville Makers Wiki

Site Tools

Page locked

Page Tools