shapeoko_3_cnc_router
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
shapeoko_3_cnc_router [2016/05/29 14:15] 24.182.94.75 [Usage Notes] |
shapeoko_3_cnc_router [2016/12/28 15:18] 66.190.155.97 [Usage Notes] |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| PLEASE NOTE: You may **NOT** use this machine prior to being checked out on it. | PLEASE NOTE: You may **NOT** use this machine prior to being checked out on it. | ||
| - | **Owner/Loaner**: TBD \\ | + | **Owner/Loaner**: Asheville Makers \\ |
| - | **Donated By**: TBD \\ | + | **Donated By**: Steve A. \\ |
| **Serial Number**: N/A \\ | **Serial Number**: N/A \\ | ||
| **Make/Model**: [[http://carbide3d.com/shapeoko/|Shapeoko 3]] \\ | **Make/Model**: [[http://carbide3d.com/shapeoko/|Shapeoko 3]] \\ | ||
| - | **Arrival Date**: TBD \\ | + | **Arrival Date**: June 2016 \\ |
| + | **Assembly Guide**: [[https://drive.google.com/open?id=0ByE4uXHeoDYNenhsS05yazd1OWc|Manual]]\\ | ||
| **Working Condition**: yes \\ | **Working Condition**: yes \\ | ||
| **Contact**: Steve A. \\ | **Contact**: Steve A. \\ | ||
| Line 16: | Line 17: | ||
| ==== Usage Notes ==== | ==== Usage Notes ==== | ||
| - | === General === | + | === Class Materials === |
| + | * [[https://drive.google.com/open?id=10IlcqnPNnpf4Khr_hTe_sQKYdcUZgd8OPOhvtuL0xMw|Presentation]] | ||
| + | * [[https://drive.google.com/open?id=0ByE4uXHeoDYNOUFOZ0xQQy1VeGs|Files for cutting coaster in pine]] | ||
| + | * [[https://drive.google.com/open?id=0ByE4uXHeoDYNOVJTNHUxd01SVmc|Files for cutting coaster in poplar]] | ||
| - | ===Fusion 360 === | + | === General === |
| + | * Securing the Stock - One good method for securing your stock is to use super glue, activator, and masking tape as described in [[https://www.youtube.com/watch?v=3uTsQ3dYRrk|this video]]. | ||
| + | === Fusion 360 === | ||
| * For post processing, choose carbide3d.cps for the Post Configuration. | * For post processing, choose carbide3d.cps for the Post Configuration. | ||
| * To engrave with a V bit in Fusion 360 (e.g. lettering), you can select a chamfer mill as your bit and then edit the bit to create the appropriate V bit. For example, you can create a 1/4 inch 90 degree V bit with the following settings: Diameter - 0.25 in; Shaft Diameter - 0.25 in; Taper Angle 45 deg; Tip Diameter - 0.001 in. | * To engrave with a V bit in Fusion 360 (e.g. lettering), you can select a chamfer mill as your bit and then edit the bit to create the appropriate V bit. For example, you can create a 1/4 inch 90 degree V bit with the following settings: Diameter - 0.25 in; Shaft Diameter - 0.25 in; Taper Angle 45 deg; Tip Diameter - 0.001 in. | ||
| + | * For poplar, cutting 5mm depth, a feed rate of 600 mm/sec gave good results. At 800 mm/sec, the CNC would skip teeth on the belts. | ||
shapeoko_3_cnc_router.txt · Last modified: 2017/10/11 10:42 by 66.190.155.97
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
