laser_cutter_engraver
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
laser_cutter_engraver [2016/11/28 19:27] 66.190.155.97 [Settings] |
laser_cutter_engraver [2019/07/02 13:01] (current) 96.36.234.213 |
||
|---|---|---|---|
| Line 12: | Line 12: | ||
| **Manual**: Located in bag on shelf above machine | **Manual**: Located in bag on shelf above machine | ||
| + | ====Maintenance==== | ||
| + | Chassis Cleaned and Lubricated: 1/7/18 \\ | ||
| + | Mirrors Cleaned: 04/10/18 \\ | ||
| + | Lens Cleaned: 4/10/18 \\ | ||
| + | |||
| + | Chassis should be lubricated with sewing machine oil. | ||
| + | Mirrors should be cleaned using a cotton swab and alcohol. Start in the center of the mirror and rotate out to the edges. | ||
| + | The lens can be cleaned in the same manner as the mirrors. Unlike the mirrors, the lens must be removed from the laser in order to clean it. Take care to avoid touching the lens surface with your fingertips, and be sure to reinstall the lens with the correct orientation (concave face should face up). | ||
| + | |||
| + | How to Check Plastic Materials for Chlorine (deadly gas that also damages laser): [[https://hackaday.com/2015/03/14/how-to-identify-plastics-before-laser-cutting-them/|https://hackaday.com/2015/03/14/how-to-identify-plastics-before-laser-cutting-them/]] | ||
| ====Usage Notes==== | ====Usage Notes==== | ||
| * DO NOT use this machine if you have not been checked out on it. Members who can check you out include Tim, Zak, Avi, and Steve. | * DO NOT use this machine if you have not been checked out on it. Members who can check you out include Tim, Zak, Avi, and Steve. | ||
| Line 35: | Line 45: | ||
| Cut Speed: 10 Power: 60 | Cut Speed: 10 Power: 60 | ||
| Engrave Speed: 200 Power: 20 | Engrave Speed: 200 Power: 20 | ||
| + | ==3mm (1/8") acrylic/plexiglass== | ||
| + | Cut Speed: 1.75"/s Power: 60W Passes: 3 | ||
| ==Soft Pine== | ==Soft Pine== | ||
| Engrave Speed: 250 Power: 30 | Engrave Speed: 250 Power: 30 | ||
| Line 45: | Line 57: | ||
| Cut Speed: 10 Power: 60 | Cut Speed: 10 Power: 60 | ||
| Engrave Speed: 200 Power: 20 | Engrave Speed: 200 Power: 20 | ||
| + | ==1/4 in. plywood New 2" PL Lens== | ||
| + | Cut Speed: 15 Power: 55-60 | ||
| ==Corrugated Cardboard== | ==Corrugated Cardboard== | ||
| Cut Speed: 40 Power: 45 | Cut Speed: 40 Power: 45 | ||
| + | Engrave Speed: Power: | ||
| + | ==Very Thin Wood Veneer== | ||
| + | Cut Speed: 100 Power: 40 | ||
| Engrave Speed: Power: | Engrave Speed: Power: | ||
laser_cutter_engraver.1480361279.txt.gz · Last modified: 2016/11/28 19:27 by 66.190.155.97
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
